![]() ![]() And that's a very conservative estimate-you may need a manufacturer-specific camera for your new head unit, and of course, the price of a new head unit depends entirely on which features you want. If you choose to buy a new head unit with your backup camera, you can expect to pay at least $400 before installation. While the name Garmin might conjure fond memories of a decade-long sweet spot. Extremely poor low-light visibility due to lens flares. And if you need professional installation, which is probably the case, it'll cost you an extra $100 or more. Requires separate compatible Garmin GPS display unit. That said, advanced features (like an integrated dashcam or DVR functionality) will quickly push the price up to $200 or $300. These kits start around $120 and are relatively easy to install. Related: Everything You Need to Upgrade Your Older Car's Audio But you will need to drop some extra cash on a backup camera kit, which will include a dashboard video screen or a rearview mirror with an integrated display. The problem, of course, is that your older car probably doesn't have a head unit or "infotainment center" capable of displaying a backup camera's feed.Īs I mentioned earlier, you don't need to upgrade your head unit to use a backup camera. Most models run between $30 and $70, with some going for even less. On their own, backup cameras are shockingly cheap. You may also want to buy a wireless camera, which eliminates the need to run video cables across your vehicle. I strongly suggest buying a backup camera with night vision and parking guide lines. Once you choose which form-factor is right for you, it's time to hunt for features. Along the right side trunk support arm there is a wire loom that feeds the reverse lights and license plate light. It's usually wireless, and it either sits on top of or replaces your existing rearview mirror. This monitor doubles as a mirror and a screen. Cameras with Mirror Monitors: For a cleaner setup, you can buy a camera kit with a rearview mirror monitor.These kits are usually wireless, so they're a great low-cost option if you aren't confident dealing with wires. Cameras with Dashboard Displays: Some backup camera kits come with a small display that sits on your dashboard or sticks to your windshield.(I strongly suggest buying an add-on backup camera from your head unit's manufacturer to make installation easy.) That said, they require a head unit or "infotainment center" that's capable of playing video. Retrofit Cameras: These backup cameras connect directly to your head unit, giving you a video feed when you go in reverse. ![]() Run the wire through the car and hide it under the sill plates.Here are the three types of backup camera: Run the camera's wire through the trunk's extension arm. Remove the bolts from the trunk handle and pull it out. Remove the plastic pieces and pry the trunk lid liner out. Connect the wire to the MMI and reinstall the MMI, then the glove box bolts and dash side panel. Run the wire for the camera through the trunk's extension arm and through the car, tucking it inside of the sill plates to hide it. Remove the two nuts that hold the trunk handle in place, then install the camera handle in its place. You don't have to remove the entire cover, just enough to the point where you can fit your arm inside. Pop the trunk and remove the trunk lid liner by first removing the plastic bits that hold it in place, then prying up to release them. Feed the wiring through the MMI slot in the glove box. With the glove box loose, you will be able to move it around if necessary. Disconnect the camera and feed the wiring through the MMI slot in the glove box, which can prove to be a big challenge. At this point, it's a good idea to test the camera and make sure that it is working properly. For just slightly more than eRapta's ERT01, this backup camera features a 1080p high-resolution image sensor that is a larger 1/2.7 size. Take the video module included with the backup camera kit and install the supplied wiring as shown in Figure 6. Step 2 – Connect the backup camera wiring Remove the wiring harness from the back of the MMI. Remove the side panel on the passenger side of the dash. Pull the MMI out and remove the wiring harness from the back. Remove the radio/MMI unit using the radio keys, then remove the blue and green sockets by prying up on the small tabs inside them. Pry the two plastic snap fittings loose, which are located on the left and right front edge of the glove box. Remove the eight bolts inside the glove box (three on the top, two on the bottom corners, two in the rear, and one on the side). Begin by removing the side panel on the passenger side of the dash by gently prying it loose with a flat head screwdriver (look for the slot near the bottom). ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |